We're here to help.
Welcome to a New Era

Aera provides unprecedented capabilities to fully control fragrance intensity - from the slightest hint to a transportive experience.
You can easily adjust scent level with two buttons on the device or use the AeraForHome app for enhanced controllability and scheduling functionality.

Quick Start Guide
Your Aera Device can be easily operated with three buttons.
Step 1

Connect the power cord to Aera and plug into a standard wall outlet.

Step 2

Cut open the bag holding the fragrance capsule (it will not tear).

Step 3

Holding capsule upright, remove the bottom (larger) plug first. If you invert the capsule to remove the plug, turn upright and allow a few moments for the fragrance to drain back into the capsule reservoir and avoid skin contact with fragrance oils.

TIP: The plugs may have a tiny amount of pure fragrance residue. Use a tissue to remove and do not place on wood or delicate surfaces.

Step 4

Slowly remove the (smaller) plug from the top of the capsule. Pulling too fast could create a vacuum effect that may release drops of fragrance to the surface of the capsule.

NOTE: Use provided replacement plugs to reseal fragrance capsule(when not in use).

Step 5

Press the power button at the back of the device to turn on. Check to make sure the LED lights on top of the device are on.

Step 6

Insert the fragrance capsule into the device and press down a ¼ inch. When inserted properly, the capsule will start to move down on its own in second or two.

CAUTION: Do not force the capsule into the device.

Step 7

Set the fragrance intensity by pressing the "+" and "-" buttons. The LED lights will indicate the current level (1-10). A quiet hum means the device is running properly. Aera will run intermittently according to the level indicated by the LED lights.

TIP: Start scenting at a low level and evaluate the scent after about 5 minutes before increasing the intensity.

IMPORTANT: Keep nose clear from fragrance output when Aera is in operation. Instead, wave air towards nose to experience fragrance.

To replace the fragrance capsule or to change fragrances, press the eject button, wait for the lift mechanism to raise the capsule, and pull up lightly to release.

Troubleshooting

Here's a key to understanding and troubleshooting potential issues with your Aera device,
if you notice any abnormal flashing LED lights.

Flashing LED Light Cycle Definition / Action
Up and Down (1-10, 10-1,1-10, etc.) Eject and Re-insert Capsule
Fade In and Out (all lights) Eject and Replace Capsule
Cycle (1-10, 1-10, etc.) Reboot Device (Unplug for 3 seconds; Plug in and Power On)
Bookend (1/2, 9/10) Wi-Fi Issue: Check Wi-Fi Connection
All Lights Blinking Fast Firmware Issue: Call Customer Care
Additional Questions?

Please contact Aera Customer Support at support@aeraforhome.com, call 1-844-LUVAERA (588-2372), or vist the help section.

Factory Reset
To reboot your device please follow these steps.
  1. Press and hold both "+" and "-".
  2. Wait for 10 seconds and release both.
  3. All 10 lights will blink once, signaling the start of the reboot.
  4. Wait 15 seconds.
  5. All 10 lights will blink three times, signaling the completion of the reboot.
App Start Guide

You Aera device(s) can be controlled remotely from a smartphone via the AeraForHome app. The setup process differs slightly between iPhone and Android. Please select the correct platform below.

Download the app from the Apple App Store and start scheduling your custom home fragrance experience.

  1. Make sure your Aera device is powered on. (Refer to the Quick Start Guide to get your device manually set up.)
  2. Make sure that your phone and the Aera device are within range of your Wi-Fi access point.
  3. Sign up for the app by creating a user name and password.
  4. After signing in, go to your phone Settings, Wi - Fi. Look for the Aera Device Network: select, and return back to the app.
  5. Once back in the app, select your home or local network. You will need your home Wi-Fi password to connect your device.
  6. Follow the on-screen instructions to rename your Aera device based on the room where it will reside.

Download the app from the Google Play Store and start scheduling your custom home fragrance experience.

  1. Make sure your Aera device is powered on. (Refer to the Quick Start Guide to get your device manually set up.)
  2. Make sure that your phone and the Aera device are within range of your Wi-Fi access point and your phone’s Wi-Fi is turned on.
  3. Sign up for the app by creating a user name and password.
  4. Connect your device and wait for your phone to find the device. Select your Aera device.
  5. Select your home or local network. You will need your home Wi-Fi password to connect your device.
  6. Follow the on-screen instructions to rename your Aera device based on the room where it will reside.

With the app you can power on/off your Aera device and change fragrance intensity from the home screen. Use the scheduler to plan automatic home fragrancing at days and times that suit your preferences.

For further support go to our Get Help section or contact us:

1-844-LUVAERA (588-2372)
support@aeraforhome.com